- Produktformular:
- Fertig gemischt
- Für die Nutzung in Außenbereich geeignet:
- Ja
- Beste Verwendung:
- Holz
- Oberflächentyp:
- Satin-Oberfläche
- Volumen:
- 2,5 l
- Oberflächenabdeckung:
- 16 m²/L
- Name der Farbe:
- Walnut
- Zusammensetzung:
- Solvent-based
- Opazität:
- Durchscheinend
- Anzahl an Beschichtungen:
- 2
- Anzahl an Beschichtungen Hinweis:
- New/bare wood - 2 coats onto Cetol HLS Plus; Maintenance - 2 coats
- Empfohlene Schichtdicke (trocken):
- 18 µm
- Trocknungszeit:
- 3 h
- Überlackierbar nach:
- 16 h
- Flüchtige organische Verbindungen (VOC) Inhalt:
- 400 g/l
- Gehalt an flüchtigen organischen Verbindungen (VOC) Kennzeichnungssystem:
- Hoch (25 - 50%)
- Werkzeugreinigung:
- Clean brushes and equipment with brush cleaner immediately after use. If spilled, Cetol Filter 7 plus may be removed immediately while still wet,using white spirit
- Anwendung:
- Ensure product is thoroughly stirred before and during application, otherwise sheen and colour variations may be experienced.
Cetol Filter 7 plus is supplied ready for use. Do not thin.
Cetol HLS plus should be used as a basestain for joinery items prior to coating with Cetol Filter 7 plus. For best results use a good quality, long-haired soft bristle brush.The product should be applied in a full flowing coat, laying off in the direction of the grain, using the minimum number of
brushstrokes necessary to produce an acceptable finish. Avoid overbrushing, as this will reduce the protection afforded. Applyto a minimum wet film thickness of 55 micrometres.
Conditions - Do not apply if there is a risk of rain, or when air/substrate temperatures are below 5ºC or above 30ºC during
application or drying periods. Protect from frost and rain until dry.Failure to meet these requirements may adversely affect the drying, visual quality and durability of the finish.Two coats of Cetol Filter 7 plus should be applied, allowing a minimum of 16 hours drying time between coats. On new work, where practical, the first coat should be applied all round prior to fixing. The second coat should be applied to all exposed surfaces, as soon as possible after the first coat has dried, but no sooner than 16 hours.
- Vorgehensweise beim Speichern:
- Store in cool, dry, frost-free conditions
- Oberflächenvorbereitung:
- Ensure the timber surface is suitably prepared, clean and dry, with dust, dirt, wax and grease removed, and allowed to acclimatiseto its end-use environment. The moisture content should not exceed 18% prior to coating.Degrease any exposed bare timber surface by wiping with a cloth dampened in a suitable solvent. Certain timber species contain high levels of natural wood extractives or exudates and some softwood can be highly resinous. Resinous deposits should be removed
with a scraper. Any remaining residues should be removed using a lint-free cloth dampened with a suitable solvent, frequently changing the face of the cloth. Allow solvent to evaporate fully before overcoating. The use of both eye and hand protection is strongly advised.
We do not recommend the use of “knotting agents” with translucent finishes as they are not always fully effective in “sealing in” resin,the presence of knots is often highlighted and adhesion of coatings can be impaired.When filling, be sure to use fillers specifically designed for use with timber. General or all purpose fillers are not suitable, particularly on external areas, as they cannot cope with timber movement and work loose.Where a superficial application of preservative to softwood and hardwood is deemed necessary, such as timbers in Durability Class 3 or lower, use Cuprinol Wood Preserver Clear (BP). For Class 4 (in ground contact) and 5 (marine) use pre-treated wood specific for these conditions. Preservative pre-treatments must be fully dry before the application of Cetol Filter 7 plus. Do not use on substrates which have had water-repellent preservative pre-treatments applied. Where possible, the first coat should be applied all round prior to fixing.
Only use non-ferrous screws, nails and fixings.Base stained joinery : Denib using a fine grade nylon abrasive pad or a fine grade (P240 or finer) wet or dry silicon carbide abrasive paper, in the direction
of the grain. Do not break through the surface coating. Remove all dust.
To ensure optimum durability and uniformity of appearance, we recommend the use of a coat of Cetol HLS plus prior to finishing.
Note: Where there is localised damage, or deterioration has occurred as a result of exposure of the factory coating for longer than 3 months, affected areas should be thoroughly sanded back to a sound substrate.All damaged or decayed timber must be removed and replaced, cutting at least 25mm into sound timber. We do not recommend the use of wood hardeners. When splicing in new sections of timber, consideration should be given to the use of a timber species whose natural durability is sufficient. Brush apply two coats of Cuprinol Wood Preserver Clear (BP) to saturation. Ensure timbers are thoroughly treated, especially any end grain sections, and are fully dry before splicing in. Secure with non-ferrous fixings and fill all voids surrounding the spliced-in area with a suitable repair compound such as Dry-Flex from Repair Care
- Verpackungsbreite:
- 188 mm
- Verpackungstiefe:
- 170 mm
- Verpackungshöhe:
- 157 mm
- Menge pro Packung:
- 1 Stück(e)
- Lagenanzahl auf Palette:
- 6
- Menge pro Schicht:
- 36 Stück(e)
- Menge je Palette:
- 216 Stück(e)
Sikkens Cetol Filter 7 Plus Dickschicht Holzlasur Nussbaum 2500mlBesonders hochwertige, seidenglänzende Dickschichtlasur (Long-Life-Lasur) für außen.
Bietet für einheimische und tropische Laub- und Nadelhölzer einen langlebigen Schutz mit hoher brillanter Transparenz. Das Produkt besitzt eine extrem hohe UV-Beständigkeit und UV-Absorptionsfähigkeit für maßhaltige Holzbauteile, Fenster, Türen etc. Daher stark gesteigerter Verwitterungsschutz für die Lasurbeschichtung und darunterliegende Holzoberflächen. Die wasserabweisende Oberfläche und die hohe Wasserdampfdurchlässigkeit unterstützen die Langlebigkeit der Beschichtung. Leichte Verarbeitbarkeit und einfache Wartung tragen zur Wirtschaftlichkeit bei. Das Produkt ist mit einem Konservierungsmittel zum Schutz des Filmes vor Mikroorganismen ausgestattet und darf deshalb nicht im Innenbereich eingesetzt werden. Anmerkung: Fenster und Außentüren – auch deren Innenseiten – gehören nicht zu Innenräumen.
Verordnung (EG) Nr. 1272/2008: entfällt
Gefahrenpiktogramme: entfällt
Signalwort: entfällt
Gefahrenhinweise: entfällt
Sicherheitshinweise:
P101 Ist ärztlicher Rat erforderlich, Verpackung oder Kennzeichnungsetikett bereithalten.
P102 Darf nicht in die Hände von Kindern gelangen.
P262 Nicht in die Augen, auf die Haut oder auf die Kleidung gelangen lassen.
P271 Nur im Freien oder in gut belüfteten Räumen verwenden.
Zusätzliche Angaben: Die beim Umgang mit Chemikalien üblichen Vorsichtsmaßnahmen sind zu beachten. Bei Schleifarbeiten generell Staubmaske tragen.
2.3 Sonstige Gefahren Mit dem flüssigen Produkt getränkte Lappen nach Gebrauch sofort auswaschen oder in einem luftdicht geschlossenen Metallgefäß aufbewahren (Selbstentzündungsgefahr!).
Sikkens Cetol Filter 7 Plus sicher verwenden. Vor Gebrauch stets Kennzeichnung und Produktinformation lesen.
Akzo Nobel Deco GmbH
Geschäftsbereich Profi: Sikkens
Am Coloneum 2
50829 Köln
Eigenschaften:
- seidenglänzende, lösemittelbasierende Dickschichtlasur
- Optimale Haltbarkeit und UV-Beständigkeit durch neuartige Filter Technologie
- hohe Transparenz
- wasserabweisende Oberfläche
Anwendungsbereich:
- Ideal für Fenster und Türen ( maßhaltige Bauteile)
- zum langlebigen Schutz von besonderen Holzbauteilen
Verarbeitung:
- das Material ist streichfähig eingestellt
- der Untergrund muss trocken, saugfähig und Schmutz-/Fettfrei sein
- bei Erstbehandlung Grundierung notwendig!
Sikkens Cetol Filter 7 Plus
DICKSCHICHTIGE HOLZLASUR DER SPITZENKLASSE - FERTIGTÖNE
- Advanced Filter Technology: Optimierte Rezeptur für höchste Haltbarkeit und UV-Beständigkeit
- Lösemittelhaltig
- Nur für außen
- Ideal für maßhaltige Bauteile wie Fenster und Türen
- Stark gesteigerter Verwitterungsschutz
- Sehr hohe Transparenz
- Extra hohe UV-Absorptionsfähigkeit
Merkmal | Ausprägung |
---|
Farbe | Eiche Hell/Eiche Dunkel/Teak/
Nussbaum/Kiefer/Altkiefer/Esche/Mahagoni
Ebenholz/Palisander |
Anwendungsbereich | Außen |
Art | Lasur |
Anwendungsbereich | |
Merkmal | Ausprägung |
---|
Gebindegröße | 0,5/1/2,5 l |
Marke | Sikkens |
Typ | Dickschicht |
Lösemittelart | Lösemittelhaltig |
Merkmal | Ausprägung |
---|
Ergiebigkeit | 17 m²/l |
Dichte | 0,93 kg/l |
Verbrauch | ca. 60 ml/m² |
Glanzgrad | Seidenglänzend |
Verarbeitungstemperatur | 5 - 30 °C; rel. Luftfeuchtigkeit: max. 85 % |
Merkmal | Ausprägung |
---|
Verarbeitung | |
Verdünnung | Lösemittel |
Werkzeugreinigung | Testbenzin |
Trocknungszeit | 3 - 16 Stunden |
Merkmal | Ausprägung |
---|
VOC Inhalt | Max. 400 g/l VOC |
de. Sie sind auf der Suche nach Produkten der Firma Sikkensund mehr und möchten diese Online oder direkt im Store kaufen? Dann sind Sie bei uns genau richtig!Proma-farben.de oder vor Ort im Farbe- und Lasuren- fachhandel bei ProMa Farben & Lacke Hamburg.
Seidenglänzende Dickschichtlasur (Long-Life-Lasur) für außen. Bietet für einheimische und tropische Laub- und Nadelhölzer einen langlebigen Schutz mit brillanter Transparenz. ist die ideale Lasur für maßhaltige Holzbauteile.
Durch die neue Advanced Filter Technology erzielt die lösemittelhaltige Dickschichtlasur höchsten Wetterschutz mit perfektem transparenten Finish. Premium-Schutz für hochwertiges Holz.
- Advanced Filter Technology: Optimierte Rezeptur für höchste Haltbarkeit und UV-Beständigkeit
- Ideal für maßhaltige Bauteile wie Fenster und Türen
- Stark gesteigerter Verwitterungsschutz
- Sehr hohe Transparenz
- Extra hohe UV-Absorptionsfähigkeit
- Geeignet für die Verwendung innen:
- Ja
- Beste Verwendung:
- Tür, Fenster
- Farbe Holzbeize:
- Braun
- Oberflächentyp:
- Satiniert-glänzende Oberfläche
- Volumen:
- 2,5 l
- Oberflächenabdeckung:
- 16 m²/L
- Name der Farbe:
- nussbaum
- Bindungssubstanz-Typ:
- Alkydharz
- Zusammensetzung:
- Solvent-based
- Flächendeckungsgrad (max.):
- 17 m²/L
- Für Materialien geeignet:
- Hartholz, Weichholz
- Opazität:
- Durchscheinend
- Anzahl an Beschichtungen:
- 2
- Trocknungszeit:
- 16 h
- Überlackierbar nach:
- 16 h
- Flüchtige organische Verbindungen (VOC) Inhalt:
- 400 g/l
- Gehalt an flüchtigen organischen Verbindungen (VOC) Kennzeichnungssystem:
- Hoch (25 - 50%)
- UV-Schutz:
- Ja
- Wetterfest:
- Ja
- Verwässerungshinweis:
- Unverdünnt verarbeiten. Falls notwendig mit Wasser.